Hedgehog VM credentials update

Updating the core user password and SSH authorized keys on the Hedgehog control node VM

Purpose

The Hedgehog control node VM runs Flatcar Linux. Flatcar manages SSH authorized keys through the update-ssh-keys tool — direct edits to ~/.ssh/authorized_keys are overwritten on every reboot because Flatcar regenerates that file from its registered key sources. Use update-ssh-keys for all key changes.

This procedure is performed via virsh console on the hypervisor host. It must be carried out during the bootstrap process, while the hedgehog-controller Ansible play is waiting for SSH access (see Operator Overview).

Prerequisites

• Console access on the hypervisor host running the Hedgehog VM
• The environment SSH public key — the public half of the key referenced by ansible_ssh_private_key_file in inventory.yml for the hedgehog_control host group (required to unblock Ansible's SSH wait)
• SSH public keys for any individual operators who need direct access

Step 1: Open a console session

On the hypervisor host:

virsh console <hedgehog-vm>

Steps 2–6 are run inside this console as the core user.

Step 2: Change the core user password

sudo passwd core

Enter the new password when prompted.

Step 3: Identify the provisioning key

update-ssh-keys -l

At this point only one key is registered — the bootstrap key baked into the installer ISO. Its name may vary; it will be the only entry listed. Note the name; it will be removed in Step 6.

Step 4: Add the environment SSH key and any operator keys

Add the environment SSH key first, using a recognisable name (for example, the environment name):

echo "ssh-ed25519 AAAA... comment" | update-ssh-keys -a <environment-key-name>

Then repeat for each operator who needs direct access, using the operator's username as the key name:

echo "ssh-ed25519 AAAA... comment" | update-ssh-keys -a <operator-name>

After each addition, confirm the key was registered:

update-ssh-keys -l

Step 5: Exit the console and verify SSH access

Log out of the core session:

exit

Detach from the virsh console (back to the hypervisor shell):

Ctrl+]

From the bastion node, verify the environment key works — Ansible needs this to be successful before its SSH wait unblocks:

ssh -i ~/.ssh/id_ed25519 core@<hedgehog-control-ip> "hostname"

Each operator should also verify their personal key at this point.

警告

Do not proceed to Step 6 until all keys have been verified. This is the last safe rollback point.

Step 6: Remove the provisioning key

Re-enter the console:

virsh console <hedgehog-vm>

Remove the provisioning key using the name noted in Step 3:

update-ssh-keys -d <provisioning-key-name>

Confirm it is absent:

update-ssh-keys -l

One entry per registered key should remain; the provisioning key must not appear.

Exit and detach:

exit

(Ctrl+] to detach)

Step 7: Reboot and verify persistence (post-bootstrap only)

警告

If you are following this runbook as part of the initial bootstrap, stop here and return to the deployment guide. Rebooting the VM while the hedgehog-controller Ansible play is still running will cause it to fail. Come back to this step after the full bootstrap (including Phase 3) has completed.

From the hypervisor host:

virsh shutdown <hedgehog-vm>
virsh start <hedgehog-vm>

Once the VM is back up, confirm SSH still works:

ssh -i ~/.ssh/id_ed25519 core@<hedgehog-control-ip> "hostname"

注記

Changes made with update-ssh-keys persist across Flatcar reboots. Direct edits to ~/.ssh/authorized_keys do not — Flatcar regenerates that file from its registered key sources on each boot.

Verify

• sudo passwd core completed without error
• update-ssh-keys -l shows all expected keys; the original provisioning key is absent
• SSH succeeds with the environment key and each operator key before reboot
• SSH succeeds with the environment key and each operator key after reboot